Objectives

· Configure hostnames and IP addresses on 2 Cisco Internetwork Operating system (IOS) switches using the command-line user interface (CLI).· use Cisco IOS commands to clues or limit access to the device configurations.· use IOS regulates to conserve the running configuration.· Configure 2 host gadgets with IP addresses.· Verify connectivity between the two PC end devices.

You are watching: Packet tracer - skills integration challenge 2.4.1.2

Scenario

As a freshly hired LAN technician, her network manager has actually asked girlfriend to show your ability to configure a little LAN. Her tasks include configuring initial setups on 2 switches using the Cisco IOS and configuring IP address parameters ~ above host devices to provide end-to-end connectivity. You are to use 2 switches and two hosts/PCs on a cabled and also powered network.

Requirements

· use a console link to access each switch.· surname ASw-1 and also ASw-2 switches.· use the R4Xe3 password for all lines.· use the C4aJa secret password.· Encrypt all clear message passwords.· incorporate the indigenous warning in the message-of-the-day (MOTD) Banner.· Configure addressing because that all devices according to the Addressing Table.· save your configurations.· Verify connectivity in between all devices.

Note: Click Check Results to watch your progress. Click Reset Activity to generate a new set of requirements. If you click this prior to you finish the activity, every configurations will be lost.

See more: Q: What Has 2 Hands But No Arms And Legs, 60 Riddles For Your Kids

Instructions:

The following information is for the Instructor variation only.This task uses variables that are randomly generated each time the activity is open up or the “Reset Activity” switch is clicked. Return the tables below show device names mapping to certain address schemes, the names and addresses are not tied together. For example, a student could get the maker names displayed in scenario 1 through the addressing shown in scenario 2. In addition, one of three execution of the topology will certainly be gift to the student.

Topology Isomorphs

Example


*

*

Switch>enableSwitch#configure terminalSwitch(config)#hostname ASw-1ASw-1(config)#line console 0ASw-1(config-line)#password xAw6kASw-1(config-line)#loginASw-1(config-line)#exitASw-1(config)#line vty 0 4ASw-1(config-line)#password xAw6kASw-1(config-line)#loginASw-1(config-line)#exitASw-1(config)#enable mystery 6EBUpASw-1(config)#service password-encryptionASw-1(config)#banner motd #warning#ASw-1(config)#interface vlan 1ASw-1(config-if)#ip deal with 10.10.10.100 255.255.255.0ASw-1(config-if)#no shutdownASw-1(config-if)#exitASw-1(config)#exitASw-1#copy running-config startup-config

Switch>enableSwitch#configure terminalSwitch(config)#hostname ASw-2ASw-2(config)#line console 0ASw-2(config-line)#password xAw6kASw-2(config-line)#loginASw-2(config-line)#exitASw-2(config)#line vty 0 4ASw-2(config-line)#password xAw6kASw-2(config-line)#loginASw-2(config-line)#exitASw-2(config)#enable mystery 6EBUpASw-2(config)#service password-encryptionASw-2(config)#banner motd #warning#ASw-2(config)#interface vlan 1ASw-2(config-if)#ip attend to 10.10.10.150 255.255.255.0ASw-2(config-if)#no shutdownASw-2(config-if)#exitASw-2(config)#exitASw-2#copy running-config startup-config